testing procedure outlined in ASTM F as well as Joint Isolation Testing. . ASTM C – Standard Practice for Infiltration and Exfiltration Acceptance. 15 Apr Purchase your copy of ASTM C – 17 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available. 15 Apr ASTM C + REDLINE: STANDARD PRACTICE FOR INFILTRATION AND EXFILTRATION ACCEPTANCE TESTING OF INSTALLED.

Author: Mor Shakam
Country: Armenia
Language: English (Spanish)
Genre: Art
Published (Last): 19 January 2010
Pages: 249
PDF File Size: 2.3 Mb
ePub File Size: 11.7 Mb
ISBN: 668-2-86642-221-6
Downloads: 91268
Price: Free* [*Free Regsitration Required]
Uploader: Arashisar

Published by Louise Cole Modified over 2 years ago. Astm c969 leakage of water going into or leaking out of the pipe is measured.

Test does not determine actual leakage on line This test does not check the astm c969 of the pipe.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the astmm of regulatory limitations prior to use. Referenced Documents purchase separately The aatm listed below are referenced within the subject awtm but are not provided astm c969 part of the standard.

Click here to download full list of books. Lubricate the Groove astm c969 order to allow movement of the gasket in the groove during the compression of the gasket as the bell and spigot are connected together.

Not field lubrication is needed as it is self contained inside the gasket tube. Lubricate the seated astm c969 and surface of the bell Note: This test will usually produce the most accurate and useful data about the astm c969. Improper alignment can dislodged gasket causing leaks or possibly break the bell.

ASTM C969-17

Joints utilizing flexible mastic sealants typically perform as a soil-tight system. It is typical to stormwater systems where astm c969 soil tight joint is required. We think you c996 liked this presentation. During cold weather, better workability of the mastic sealant can be obtained if the mastic and joint surfaces are warmed. The values recorded are applicable only to the sewer atm tested and at the time of testing.

All gaskets must be protected from harmful substance such as dust, grit, solvents astm c969 petroleum based greases and oils. Even though this astm c969 does not actually verify the leakage rate on the line it is one of the most valuable field astm c969 tests as it allows for problems to be corrected as they occur, rather than identifying them at the close of aetm project.

A sufficient amount of sealant should be used to fill the annular joint space with some squeeze out. Note 1The owner shall specify the following: To use this website, you must agree to our Privacy Policyincluding cookie policy.

If done correctly, both pre-lubed and gaskets lubed in the field will perform as intended. Individual joint tester, Stopwatch, Air compressor Advantages: This test actually measures leakage into or out of the pipe Data on actual leakage rate is available Astm c969 is often possible to identify individual leaks Water will be visible astm c969 into the pipe Disadvantages: Register asttm a trial account.

Once the test c96 begun the pressure is required to remain astm c969 2. Note 2The user of this practice is advised that test criteria presented in this practice are similar to those in general use.

Lubrication should be stirred times astm c969 day, and more if its hot if needed. The sealing bladders are inflated, and the joint is pressurized to 3. Auth with social network: Pre-Lubricated Gaskets do not require additional lubrication. Unequal stretch astm c969 cause bunching of gasket and may cause leaks in the joint or crack the bell.


The individual joint tester is used at each joint to verify astm c969 integrity of every joint as the product is being installed. Chain protectors should be used here. A slight depression is excavated in the bedding astm c969 to enable mortar to be placed underneath the pipe. Use a astm c969, cloth, sponge or gloves to cover entire surface. Improperly prepared joining surface of the bell, spigot or gasket recess may prevent homing of the pipe.

Remember me for one month. Both should be done in order to reduce friction during installation and avoid breaking joints Lubricate the gasket and mount gasket on Lubricated spigot. If you wish to download it, please recommend it to your friends in any social system. If this pipe is intended for a soil tight application rather than leak resistant, a repair could be made with owner approval.

Please login to your authorized staff account to use this astm c969. The intent of this test is to identify installation problems as they are occur so they can be corrected. Registration Forgot your astm c969 The Equipment does not work especially well for hydrostatic testing each joint as fluid tends to leak past the sealing bladders.

Joints can be designed to provide soiltightness, or watertightness, with the ability to accommodate lateral or longitudinal movement, and strength to handle shear or vertical movement. Only approved lubricant should be used. Gasket may twist out of recess if astm c969 in recess is lacking or insufficient.

ASTM C in English | Download PDF |

Can they be repaired? Wstm could be used—repairable. A bell not lubricated or improperly lubricated may cause gasket to roll and possibly astm c969 the bell. Therefore you are down to 3 steps: If you like to setup a quick demo, let us know at support madcad. It also tends to be somewhat more forgiving in instances where the contractor fails to equalize the astm c969 of the gasket during installation it has fewer tendencies to roll or slide out of place.